Having been a proponent of twin rudders for well over a decade, Rob Humphreys Design has a wealth of experience with the arrangement through a range of boat types, from the rather esoteric world of Open 60s and Volvo 70s through to moderately heavy cruising yachts. Our knowledge of what to do and how to do it has been partly theoretical, partly intuitive and – through feedback from our boats – partly empirical. However, it is only very recently that we have had the opportunity to really quantify the benefits. This came through an exhaustive tank testing session on behalf of the new Oyster 885, which was commissioned by Oyster on the basis it would not only benefit the development of the 885 but also the rest of the Oyster range.

In the early design brief discussions last year on the Oyster “PC” as it was code-named, the Oyster New Product Development team and I sat down and ran through their ideas for how this new yacht should fit into the range. The conclusion was a yacht with moderate beam, balancing the requirements of interior volume with boat speed, a mast further aft to provide a powerful blade jib for easy upwind sailing, and room for four owner/guest cabins in a hull length of “no more than 20 millimetres short of the LY2 MCA 24 metre rule”.

It was clear that this was going to be a bit of a sea change for Oyster. We all felt it would be helpful to have tangible reference information for those owners trying to understand the shift from a skeg-rudder to the twin rudder form for this exciting new model.

In fact our testing session set out to do more than just this because we also used the opportunity to let the spade rudder have its say, just for some form of completeness. We have often been asked why Oyster has tended to steer clear of spade rudders and the answer has more to do with potential vulnerability than any disrespect for its potential qualities. As any Oyster owner knows, a blue-water cruising yacht has to be accomplished in a number of different ways, and one of the lower profile requirements has to be an ability to slide backwards against a Mediterranean harbour wall without necessarily endangering the steering gear. One paradox of success for Oyster is that with so many boats out there, if it is possible to do something then it has usually been tried. In this case, with three SuperShoal twin rudder Oysters already on the water, the expression ‘tried and tested’ comes to mind. A spade rudder, whatever its qualities in other respects, is not quite as bomb-proof as a rudder hung off a full-depth skeg.

In our tank testing we were focusing our attention on a fully-pressed up set of sailing conditions, with the boat heeled over to 20 degrees and sailing at nine knots, with a variety of leeway angles and load conditions. Separately we had commissioned North Sails to run their proprietary CFD (Computational Fluid Dynamics) panel code ‘Flow’, to determine the exact three-dimensional centres of pressure that are relevant to Oysters, so that we could keep an eye on what was happening to the balance of the boats.

We tested a lot of other things as well, but the rudder testing was most interesting and was totally supportive of all that we had learnt to be true in the field. For a given side force and leeway angle the skeg rudder and the spade rudder were in a roughly similar ballpark, whereas the twin-rudder equivalent was in another world altogether. For example, with the twin rudders set to just two degrees to the flow, the spade rudder needed to be at over six for an equivalent moment, and the skeg-hung rudder at eight – all for the same yaw moment.

Put another way, the leeward twin rudder provided four times as much force than a skeg rudder!

Much of the distinction comes from the fact that the twin rudders are operating in clean water whereas centreline rudders – of whatever denomination – are operating in a disturbed second-hand flow coming off the keel. The result is a much more satisfying steering experience and at the same time a significant reduction in resistance – so more speed.

From our perspective, twin rudders represent a huge benefit and Oyster owners will really appreciate this development too as soon as they have the wheel at their fingertips. But what’s also interesting is that the system fares a lot better in terms of potential reliability, especially against the spade rudder. The blades are significantly smaller and more lightly loaded, and the span is considerably shorter, making it almost impossible to damage the steering gear when reversing into a quay. And of course, with two rudders rather than one, there is an obvious increase in the level of redundancy. Unlike some twin-rudder installations, the arrangement we have for Oyster means that even assuming the worst-case loss of one rudder it would still be possible to sail the boat on the compromised tack, albeit with reduced canvas.

All in all we learnt nothing new in a qualitative sense; but in quantitative terms it was certainly an eye-opener, not just for me but also for the Wolfson Unit who had not previously run such a benchmarking comparison.

With twin rudder installations already in action on Oyster 82s and an Oyster 655, and now specified as standard on the new Oyster 885, in addition to being available on the SuperShoal versions of the 54, 575 and 625, we see their use spreading through to the standard keel yachts. Watch this space for the next new model!

Related news

GH013988 1588081538269 v2
Friday 22 May 2020

Atlantic Crossing Blog

A live blog series lifting the lid on what this bucket list experience is like on an Oyster Yacht.

FIND OUT MORE
OY565 190617 BCR 149
Wednesday 29 April 2020

Preparing to cross the Atlantic

We take you through the key considerations for preparing for this exciting challenge.

FIND OUT MORE
Oyster Yachts Craftsmen
Wednesday 29 April 2020

Update from Richard Hadida CEO & Owner

FIND OUT MORE
565 Header Image
Wednesday 22 April 2020

Oyster Design Manager

An opportunity has arisen for a creative dynamic yacht designer to take responsibility for the management and developmen...

FIND OUT MORE
@